MJB V1.2 Board

Our new Magic Jelly Bean GOai board Featuring the GW2AR-18-QN88P FPGA

• 20,736-LUT4 FPGA
• On-Chip Block-SRAM 828Kbit
• 10x10mm QFN88 FPGA Package

• HDMI RX and HDMI TX
• Internal 2x32Mbit PSRAM
• On-Board 64Mbit SPI-FLASH
• LED Indicator
• OLED Display Connector
• USB Programmer
• DC5V è 3V、2.8V、2.5V、1.8V、1.2V、1.0V
• PCB Size: 6cm x 6.6cm

MiniStar Experiment Kit

Everything you need to start exploring the world of programmable logic devices. Comes with the MiniStar Embedded Computer Board, MiniStar Experiment Carrier, flex cables and prototyping wires.

MiniStar Nano Experiment Kit

The MiniStar Nano Experiment Kit is based on Gowin GW1NSR series of FPGA product. This kit comes with everything you need to start exploring the world of programmable logic devices using the MiniStar Nano. This kit includes the Ministar Nano Experiment Board and prototyping wires.

• QN48 Package
• Embedded ARM Cortex-M3 Hardcore Processor
• JTAG
• Internal Flash
• 4 - Push Buttons
• 4 - Dip Switches
• 8 - LED Indicators
• Inverse Voltage Protection
• 5V Supported

MJB Camera

The MJB Camera Board will allow you to use a OV2640 Camera Module with the MJB Board. The OV2640 is a SOC sensor that has an on-chip ISP which can do auto-exposure, auto-white balance, all in a small package. Ideal for creating great images at a miniature cost.

MJB Microphone

This tiny, low power microphone comes with an I2S digital output which allows direct interconnect with our MJB board. Ideal for smaller devices where size and power consumption are a constraint.

MJB Accelerometer

The LIS2DH12 accelerometer comes with 8 LEDs and is fully compatible with your MJB board. Accelerometers are devices that measure the change in velocity and sense vibrations within systems. A common use for accelerometers for handheld devices would be rotating a display once sensing the physical change of orientation. The LIS2DH12 accelerometer comes with 8 LEDs

MiniStar Board

Low Cost FPGA+MCU Embedded Computer Board

• GOWIN GW1NS-4C µSoC FPGA
  • 4.6K LUT FPGA Fabric
  • ARM Cortex-M3 Embedded MCU
  • Embedded 256Kbit Flash
  • 64Mbit HyperRAM
• High Speed Flex Connectors
  • Selectable IO Voltages
• USB-C to JTAG Programmer
• J-LINK Debugger Header
• 27Mhz Mems Oscillator
• 64-Mbit external SPI Flash
• 2 - Push Buttons, 
• 2 – User LEDs
• Power LED

MiniStar Experiment Carrier

Take your MiniStar board to the next level with this fully compatible experimental board. Explore your programmable logic device to the limits!

• High Speed Flex Connectors to MagicStar
• 4 – Toggle Switches
• 4 – Push Buttons
• Four Digit Seven-Segment Display
• Three 0.1” headers
• 8 - LEDs

MiniStar Nano

Low Cost FPGA+MCU Embedded Computer Board

• GOWIN GW1NS-4C µSoC FPGA
  • 4.6K LUT FPGA Fabric
  • ARM Cortex-M3 Embedded MCU
  • Embedded 256Kbit Flash
  • 64Mbit HyperRAM
• High Speed Flex Connectors
  • Selectable IO Voltages
• J-LINK Debugger Header
• 27Mhz Mems Oscillator
• 64-Mbit external SPI Flash
• Power LED
• 26mm x 17.9mm

U2X Programming Dongle

The U2X Programming dongle is developed to bridge USB to JTAG, SPI, I2C, and GPIO. This new USB solution can be used to program and communicate with FPGAs, MCUs. And other devices. Control pins for different interfaces:

• JTAG
• SPI
• I2C
• GPIO